The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
The article below about Installing A Bathtub is really insightful. Don't overlook it.
Mounting a bath tub isn't precisely rocket science, yet it does call for strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard task. If the old bathtub is conveniently easily accessible, the task can relocate rapidly; if you have to open a wall to remove the old tub as well as position the new bath tub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the new one. See to it you have qualified on your own for the job and fit attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube links.
This article will certainly aid you install a brand-new tub in your bathroom if you have actually already purchased a new bathtub and don't need to change the setup of your previous water pipelines.
Your devices as well as material list should make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted gain access to that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Before carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in location between the faucet as well as the sink. Secure the faucet in position with the supplier given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the needed position. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bathtub till the level reviews level.
To install faucets, fit the bottom of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Activate the supply of water and check all joints and also new pipework for leakages and also tighten them if required. Load the tub and also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the tub has been made use of a minimum of once as this will resolve it right into its final setting.
Planning for the Setup
First of all, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and also cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our excerpt about Installing A Bathtub. Thanks a lot for finding the time to browse our short article. You should take a moment to share this article if you enjoyed it. Thank you for your time. Don't forget to come by our site back soon.
We're on standby! Report this page